Performance Grades
PG70 – PG-70-40
Cutback RC 800
Rapid Curing 800 RC800 a combination of penetration grade asphalt cement and a diluent or cutter highly rapid in its volatility making it easier to apply. Cut back RC800 is compliant with ASTM standard for cut back asphalt.
Bitumen 10/20
Bitumen 10/20 is commonly used for the production of hot mix asphalt for the base and wearing courses.
Performance Grade Bitumen Advantages
1. Common tests are conducted at a single test temperature which is 25°C in penetration and 60°C in viscosity test, which means that they cannot give any details about how the bitumen would behave in low or high temperatures. Superpave grading indicates a working temperature range of binder and therefore, helps with choosing the best type according to the condition each project demands.
2. Empirical methods such as viscosity and penetration grading systems were developed based on old experiences and can be applicable if those conditions still exist. But,climatic and current traffic conditions are rapidly changing and past experiences can no longer be defining criteria. In the PG system, it is possible to use actual traffic volumeand vehicle speed which represents the duration of loads are applied.
3. Because of the visco-elastic properties of bitumen, the rate of load application and temperature have a great effect on its behavior. Although the behavior of bitumen in lower loading rates corresponds to that of higher temperatures, none of the other grading systems doesn’t take the rate of load into account except for Superpave. While Superpave can be easily used for both unmodified and modified bitumen, conventional methods areused only for unmodified bitumen types.
4. Conventional methods ignore the long-term aging of binders and its behavior. But Superpave takes both long-term aging using with the pressure aging vessel (PAV) and short-term aging using the rolling thin film oven test (RTFOT) into account.
5. Bitumen properties indicated at different temperatures contribute to resistance to the distresses in a different level. Bitumen contributing in a better rutting resistance is measured at maximum pavement temperatures and which leads to a more elastic and stiffer binder. Bitumen contributing to fatigue resistance is the most crucial at average pavement temperatures and it requires asofter bitumen while it still favors an elastic binder. Bitumen contribution to thermal cracking is sensitive atminimum pavement temperatures and it demands a less elastic and soft bitumen.
Specification
Description |
Unit |
Value |
Test Method |
---|---|---|---|
Average 7-day Max. Pavement Design Temp
|
°C
|
< 70
|
ASTM D6373
|
Minimum Pavement Design Temperature
|
°C
|
< -40
|
ASTM D6373
|
ORIGINAL BINDER
|
|||
Flash Point Temp, T48: Minimum
|
°C
|
230
|
ASTM D92
|
Viscosity Max. Test Temperature
|
Pa S
|
0.3
|
ASTM D4402
|
Dynamic Shear, TP5:Min 1.00 kPa test temp@10rad/s
|
KPa
|
1.00 Min
|
ASTM D6373
|
ROLLING THIN FILM OVEN (T240)
|
|||
Mass Loss, Maximum, Percent
|
%
|
1.00
|
ASTM D6
|
Dynamic Shear, TP5:Min 2.20 kPa test temp@10rad/s
|
KPa
|
2.20
|
ASTM D6373
|
PRESSURE AGING VESSEL RESIDUE (PPI)
|
|||
PAV Aging Temperature
|
–
|
100/110
|
–
|
Dynamic Shear, TP5:Max 5000 kPa test temp@10rad/s
|
KPa
|
5000
|
–
|
PHYSICAL HARDENING REPORT
|
|||
Creep Stiffness, TP1:S, Max 300.0MPa, Min0.300 test temp@60s
|
°C
|
30
|
ASTM D6648
|
Direct Tension, TP3: Failure Strain, Min 1.0% test temp@1.0mm/min
|
°C
|
30
|
ASTM D6648
|
Safe Handling and Storage
- Use Personal Protective Equipment (PPE’s) when handling (i.e. gloves, eye protectors, etc.
- Maintain safe heating temperatures when using this product.
- Avoid contact with skin, eyes and clothing.
- Avoid breathing vapor, spray or mists when applying.
Packaging
Penetration graded Bitumen PG70-10 is available in 0.6 mm thickness, 180 kg net weight drums, 95 cm height and 45 cm diameter (+/- 3 kg operational tolerance).
Drums
Keep drums in a cool, well-ventilated place.